Diesel Screw Compressor 87 CFM

DSCDM80C
  • 87 cfm / 2463 lpm
  • 799 kpa / 116 psi
  • 3 Cylinder Diesel
  • 80 Litre Fuel Tank
$8,990
inc. GST

Free Air Delivery : 87 cfm / 2463 lpm
Working Pressure : 799 kPa / 116 psi
Engine : OEM 3 Cylinder Diesel
RPM : Variable
Cooling Method : Water Cooled - Rated For Australia's North
Bore : 90 mm
Stroke : 95 mm
Displacement : 1.813 l
Rated Power / RPM :  25 / 2600
Max Torque / RPM :  102.8 / 1820
Injection : Direct
Aspiration : Natural
Controller : Digital Multi-functional Meter GM50H MKII Series
  Engine Speed
  Oil Pressure
  Oil & Water Temperature
  Battery Voltage
  Run Hours
Safety Systems : Battery Isolator
  Emergency Stop
  Failsafe Shutdown Fuel Solenoid
Noise Level : 72 dBA at 50% Load
Fuel Tank Capacity : 80 l
Running Time : n/a
Fuel Consumption : n/a
Chassis Enclosure : Lockable
  Sound Deadening Throughout
  Weather Resistant Powder Coating
  Stainless Steel Fittings
  External Use
Mine Site Ready Bunding : Yes
Air Outlet : 1x 1 Inch BSP Fitting
Options : Minespec Padlockable Battery Isolator
  Fire Extinguisher
Shipping Weight (kg) : 700 kg
Shipping Dimensions (LxWxH) : 170 x 85  x 116
Also Available : 124 cfm / 3511 lpm
  185 cfm / 5238 lpm

Rotary screw compressors provide an extremely reliable supply of clean, dry compressed air.

When deciding between rotary and piston compressors, it is important to consider duty cycle, performance, energy efficiency, air quality, maintenance, and installation costs.

Piston compressors are still the most common choice for many small compressed air system users.

For many of these applications, the relatively low air demand and quality needed make the piston a cost effective choice.

There is, however, a segment of compressed air users that may require a higher level of air quality. A collision repair shop, for example, would typically use much more compressed air and have higher air quality needs than other automotive service businesses.

Duty Cycle and Flow

An important difference between piston and rotary compressors is their duty cycle.

Duty cycle is the percentage of time a compressor may operate without the risk of overheating and causing excessive wear.

A piston compressor may provide adequate flow for a short period, but its allowable duty cycle must be considered. Most small piston compressors have an allowable duty cycle of 60-70%. For this reason, piston compressors are usually oversized to allow the compressor to periodically shut down and cool off because of the relatively high operating temperatures.

Even with adequate air storage this can cause capacity problems during peak operating hours. Further, if the shop expands or business increases, lack of air capacity can become even more of an issue.

Rotary screw compressors have a 100% allowable duty cycle and operate continuously if the need arises. This is possible because rotary compressors are fluid cooled. The fluid performs four important functions:
• Lubricates the bearings in the pump
• Removes contaminants from the air
• Forms a non-wearing seal between rotors and casing
• Removes the heat generated by compression as part of a thermostatically controlled fluid circuit.

Heat and Moisture

All of these benefits are important, but this last point is very relevant to the air quality. Piston compressors operate at internal temperatures of 300°F - 400°F, while a rotary screw compressor runs at much lower internal temperatures (between 170°F and 200°F). Just as hot summer air holds more humidity, hotter compressed air can hold more moisture and requires additional components to dry and clean it. A rule of thumb is that every 20 degree (F) increase in temperature doubles air’s ability to hold moisture.

Diesel Screw Compressor

The advantage of a diesel screw compressor is reducing the dependancy on an electrical power source, and, the ability to be mobile.
The ABLE diesel screw compressor can be moved between locations much the same way as our ABLE diesel generators using a forklift, HIAB, tilt tray, telehandler, or sling for example.

Being a mobile unit makes the diesel screw compressor perfect for service vehicle applications on farm, mine and building sites. 

No posts found

Write a review

The warranty is for 12 months or 1000 hours.

Batteries are not included in our warranty.

We warrant our products for faulty parts and defective workmanship.

This warranty does not cover misuse, incorrect or irregular maintenance and accidents during use.

If a product or part is faulty, we require it to be sent back to us including a copy of the Tax Invoice.

Once the item or part is tested and is faulty, it will be repaired or replaced under warranty.

The purchaser is responsible for all postage costs of returning any faulty item back to us and is also responsible for the postage costs incurred when we send the replacement part back to the purchaser.

Spares and Accessories for this Product

Dry Break
[Contact us for a price]
Call us for a very competitive freight price
BT85
$2,650
Call us for a very competitive freight price
Why Buy From Able Sales?

Best Prices Australia Wide

High Quality for Peace of Mind

Amazing Value for Money

Minimum 1 Year Warranty on All Machines

Backup Assured by Our Manned Workshops

Full Spare Parts Stocked Even After Warranty

Friendly, Expert Product Knowledge & Advice

National Company with East/West Branches

Able Sales Established For 12 Years Nationally

30 Years Industry Experience

Give us a call on 1300 793 001 to discuss your needs today.

Testimonials Testimonials

GeoTrust Seal - Click to Verify